This standard is issued under the fixed designation E ; the number immediately following the designation indicates the 1 This practice is under the jurisdiction of ASTM Committee E-7 on Nonde- .. Hole numbers 8 thru 12 are optional. American Society for Testing Materials ASTM-E Utilising a Fixed Line Bench12 ASTM-E and where necessary harmonises the Standard with. Hello friends, who has ASTM E? I have the version 11, don’t know the change between the two version. Thanks.
|Published (Last):||26 September 2017|
|PDF File Size:||11.95 Mb|
|ePub File Size:||13.25 Mb|
|Price:||Free* [*Free Regsitration Required]|
Yes, it might be used on a daily basis and I have seen some procedures requiring it to be tested prior each test!!! Establish a system in accordance with ANSI Z or ISO for calibration and certification of all current and voltage measuring devices, ammeter astm e1444-12, timers, lightmeters, gaussmeters, and field indicators used in verification.
Magnetic particle testing may be applied to raw material, astm e1444-12, finished and semi-finished materials, welds, and in-service parts. When testing according to ISODC electromagnets should only be used astm e1444-12 agreed at enquiry and order stages. Hi Fyant, Welcome to ndt.
ASTM E / EM – 12 Standard Practice for Magnetic Particle Testing
New ASTM E/EM Edition – Magnetic Particle Testing – Document Center’s Standards Forum
Lifting force according to ASME sec. Related Products Searching for related products Maximum detectability occurs when the discontinuity is positioned on the surface and perpendicular to the magnetic astm e1444-12.
Magnetic particle testing is not applicable to non-ferromagnetic metals and alloys such as austenitic stainless steels.
V article 7, para T Now I can get involved with a new obsession! Dear Fitra, How are you d1444-12 Register or Log in for astm e1444-12 access to additional content.
Combining values from the two systems may result in non-conformance with the standard. You can e11444-12 the complete history of the standard at our usual revision history page available astm e1444-12 every standard on our website.
Maximum detectability occurs when the discontinuity is positioned on the surface and astm e1444-12 to the magnetic flux. Also for your information, There is another standard: I was able to astm e1444-12 the 40lb lifting force in: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine astm e1444-12 applicability of regulatory limitations prior to use.
Magnetization shall be determined by measuring the tangential field strength, Ht, at the centre of a line joining the centres of the pole faces of the electromagnet with pole extenders where used. So you will need a 40lbf lifting force for DC current electromagnetic yokes with pole spacing of 3 to 6 inch astm e1444-12 you want to carry out MPI testing on Steel Forgings.
astm e1444-12 Link to Active This link will always route to the current Active version of the standard. Magnetic particle testing is not applicable to non-ferromagnetic metals and alloys such as austenitic stainless steels. This standard practice may used for verifying lifting force daily prior to use. astm e1444-12
New ASTM E1444/E1444M 2012 Edition – Magnetic Particle Testing
EB, Did you check what the Dead Sea scrolls had e14444-12 say on the subject???? It says”Changed the existing wording in T a to clarify astm e1444-12 required frequency of yoke lifting power verification. This standard has been updated more regularly there are 24 older versions before and I do not have access to older version.
Alternating current and permanent astm e1444-12 yokes shall have a lifting force of at least 10 lb [4. astm e1444-12
This practice establishes the basic parameters for controlling the application of the magnetic particle testing method.
Our astm e1444-12 staff can assist you with not astm e1444-12 your standards purchases, but other management services to insure that your collection is always up-to-date.
Direct current yokes shall have a lifting force of at least 30 lb Nwith a 2 to 4-in. The electromagnet with a pole spacing, s, is placed on a steel plate as shown in Figure 1. Guide E can be used in conjunction with this practice as a tutorial. The magnetizing power of all yokes shall be checked whenever the yoke has been damaged or repaired. This practice is written so that it can be specified on the engineering drawing, specification, or contract.
I will check them for you as soon as Astm e1444-12 have access to older versions. A weight need only be verified again if damaged in a manner that astm e1444-12 have caused potential loss of material. You can see this in the “List of changes in record number order” section, number Direct current yokes shall have a lifting force of at least astm e1444-12 lb [ This has not been changed since at least Magnetic particle testing may be applied to raw material, billets, finished and semi-finished materials, welds, and in-service parts.
Work Item s – proposed revisions of astm e1444-12 standard. Combining values from the two systems may astm e1444-12 in non-conformance with the standard. Or you may prefer to contact us by phonefax or email info document-center. Notes are optional and private. The magnetizing power of yokes shall be verified whenever the yoke has been damaged or repaired.
In this test method the source magnetic field is in the test target’s radial direction.