Last previous edition approved as C – 96e1. 8. Available from Underwriters Laboratory, Pfingsten Road, Northbrook, IL 2. Annual Book of ASTM. ASTM C Standard Specification for Laminated Architectural Flat Glass. ASTM C LAMINATED GLASS. INSPECTION PROCESS. MAXIMUM ALLOWABLE PROCESS BLEMISHES. Vertical Glazing Applications. Size up to 25 Sf.
|Published (Last):||2 May 2007|
|PDF File Size:||14.69 Mb|
|ePub File Size:||14.94 Mb|
|Price:||Free* [*Free Regsitration Required]|
Related Suppliers Searching for related suppliers Glass intended to be used primarily for architectural glazing products including: The values in parentheses are for information only. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Astm c1172 may be marked with Specifies the quality requirements for flat laminated glass consisting of two or more layers of glass bonded with an interlayer material.
Cookies are small files zstm in your browser and are used by most websites to astm c1172 your overall astm c1172. This specification covers the quality requirements of flat, transparent, clear, and tinted glass intended to be used primarily for architectural glazing products.
Edge seal durability, internal moisture formation, internal volatile fog formation, argon gas retention.
ASTM C – Standard Specification for Laminated Architectural Flat Glass | Engineering
AAMA – Glass Standards and Guidelines
Link to Active This link will always route to the current Active version of the standard. The following test methods shall be performed to meet the specified requirements: Glass Standards and Guidelines.
Cross sections of typical electrochromic windows are shown astm c1172 which devices astmm four or five-layers astm c1172 coatings that include the two or three active layers sa Point blemish, linear blemish content, associated distortion, dimension, squareness, reflectance and transmittance.
Glass strength, overall bow, v1172 bow, dimension, hole, notches and cut-out tolerances and product labeling. The values in parentheses astm c1172 for information only.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
This specification covers the quality requirements for cut sizes of flat laminated glass consisting of two or more lites of glass bonded with an interlayer material for use in building glazing. Historical Version s astm c1172 view previous versions of standard. Establishes the physical requirements for flat, heat strengthened, astm c1172 fully tempered coated and uncoated astm c1172.
Each flask shall be marked with the letter “A” to signify compliance with applicable construction and accuracy requirements. This abstract is a brief summary of the referenced standard. Mockups are recommended as a method to evaluate astm c1172.
Mockups are recommended as a method to evaluate glass.
Notes are optional and private. Provides guidelines for categorizing and qualifying unintended visual obstructions in an IGU. The following test methods shall be performed to meet the specified requirements: Presently, only aetm silicone-sealant that is specifically formulated, tested, and marketed as a structural glazing sealant is allowed It is the responsibility of the user of astm c1172 standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
This standard does not purport to address all of the safety concerns, if any, associated with its use. Related Products Searching for related products It is informational only astm c1172 not an official part of the standard; the full text of the standard astm c1172 must be referred to for its use and application.
Register or Log in for direct astm c1172 to additional content.
This astm c1172 does not purport to address all of the safety concerns, if any, associated with its use. These assemblies are capable of developing a minimum predetermined tension when installed by applying torque to the nut, while at the same time applying a counte ASTM does not give any warranty express or implied or astm c1172 any representation that the contents of this abstract are accurate, complete astm c1172 up to date.
Furnished laminated flat glass shall be classified to the following kinds: Furnished laminated flat glass shall be classified to the following kinds: